Node Programming - Revision history

Karsten: Blanked the page

2016-12-08T07:16:53Z

Blanked the page

Karsten: Karsten moved page Nodeeditors canvas to Node Programming

2016-12-08T07:15:54Z

Karsten moved page Nodeeditors canvas to Node Programming

Karsten at 12:19, 30 November 2016

2016-11-30T12:19:51Z

Karsten: /* nodeeditors canvas */

2016-11-30T12:07:07Z

nodeeditors canvas

Karsten: Created page with "== nodeeditors canvas == the following picture shows the nodeeditor canvas: image:canvas.png From the upper left to the upper right: * '''New''' - Creates a new node pro..."

2016-11-30T11:51:43Z

Created page with "== nodeeditors canvas == the following picture shows the nodeeditor canvas: image:canvas.png From the upper left to the upper right: * '''New''' - Creates a new node pro..."

New page

== nodeeditors canvas ==

the following picture shows the nodeeditor canvas:
[[image:canvas.png]]

From the upper left to the upper right:
* '''New''' - Creates a new node project - doesn't work at the moment. As a workaround you can store an empty nodefile with '''Save''' and load it back with '''Load''' when needed.
* '''Load''' - loads a stored nod-file from disk. The file extension is '''.nod'''.
* '''Save''' - stores a node project
* '''Apply''' - The Apply button commits a geometry calculated with the nodeeditor to the Moi working enviroment. After pressing the Apply button the geometry is independent from the nodeeditor.
* '''Run''' - Starts the calculation
* '''Step''' - The node project will be calculated stepwise
* '''i'''(Info) - The Info button opens the info panel for nodes - shown on the right side of the picture. Here you can look a the properties of the node and change them. It shows the actual clicked node.. You can open it also with a double click on a node.

← Older revision		Revision as of 07:16, 8 December 2016
Line 1:		Line 1:
−	~~== nodeeditors canvas ==~~

−	~~the following picture shows the nodeeditor canvas:~~
−
−	~~[[image:canvas.png]]~~
−
−	~~From the upper left to the upper right:~~
−	* '''New''' - Creates a new node project - doesn't work at the moment. As a workaround you can store an empty nodefile with '''Save''' and load it back with '''Load''' when needed.
−	* '''Load''' - loads a stored nod-file from disk. The file extension is '''.nod'''.
−	* '''Save''' - stores a node project
−	* '''Apply''' - The Apply button commits a geometry calculated with the nodeeditor to the Moi working enviroment. After pressing the Apply button the geometry is independent from the nodeeditor.
−	* '''Run''' - Starts the calculation
−	* '''Step''' - The node project will be calculated stepwise
−	* '''i'''(Info) - The Info button opens the info panel for nodes - shown on the right side of the picture. Here you can look a the properties of the node and change them. It shows the actual clicked node.. You can open it also with a double click on a node.
−
−	To move the view, press down the left mouse button in a free area of the canvas and move the mouse. With your mouse wheel you can zoom in and out. If you press down the left mouse button inside a node, you can move it around. Release the mouse button places it to the mouse position. Pressing the left mouse button on a nodes output you will start a connection. Move the mouse cursor while keeping the button pressed to the input of another node, a connection is made when relase the button there. If you press the right mouse button in a free area of the canvas, a pull down menue opens. In the sub menues you can choose the node type you want to create. The node will placed at the position where you pressed the right mouse button. Pressing the right mouse button inside a node will open a menue with options for the node like clone or remove.

← Older revision		Revision as of 12:19, 30 November 2016
Line 14:		Line 14:
	* '''i'''(Info) - The Info button opens the info panel for nodes - shown on the right side of the picture. Here you can look a the properties of the node and change them. It shows the actual clicked node.. You can open it also with a double click on a node.		* '''i'''(Info) - The Info button opens the info panel for nodes - shown on the right side of the picture. Here you can look a the properties of the node and change them. It shows the actual clicked node.. You can open it also with a double click on a node.

−	To move the view ~~you can~~ press down the left mouse button in a free area of the canvas and move ~~them around with~~ the mouse. With your mouse wheel you can zoom in and out. If you press down the left mouse button inside a node, you can move it around. Release the mouse button places it to the mouse position. Pressing the left mouse button on a nodes output you will start a connection. Move the mouse cursor while keeping the button pressed to the input of another node, a connection is made ~~between output and input~~. If you press the right mouse button in a free area of the canvas, a pull down menue opens. In the sub menues you can choose the node type you want to create. The node will placed at the position where you pressed the right mouse button. Pressing the right mouse button inside a node will open a menue with ~~other~~ options like clone or remove.	+	To move the view, press down the left mouse button in a free area of the canvas and move the mouse. With your mouse wheel you can zoom in and out. If you press down the left mouse button inside a node, you can move it around. Release the mouse button places it to the mouse position. Pressing the left mouse button on a nodes output you will start a connection. Move the mouse cursor while keeping the button pressed to the input of another node, a connection is made when relase the button there. If you press the right mouse button in a free area of the canvas, a pull down menue opens. In the sub menues you can choose the node type you want to create. The node will placed at the position where you pressed the right mouse button. Pressing the right mouse button inside a node will open a menue with options for the node like clone or remove.

← Older revision	Revision as of 07:15, 8 December 2016
(No difference)

@@ Line 2: / Line 2: @@
 the following picture shows the nodeeditor canvas:
 [[image:canvas.png]]
@@ Line 12: / Line 13: @@
 * '''Step''' - The node project will be calculated stepwise
 * '''i'''(Info) - The Info button opens the info panel for nodes - shown on the right side of the picture. Here you can look a the properties of the node and change them. It shows the actual clicked node.. You can open it also with a double click on a node.