Full Version: Nodebundle for playing with nodes

Show messages:  1-8  …  289-308  309-328  329-348  349-368  369-388  389-408  409-428  …  1849-1859

Thread Split: Some posts in this thread have been moved here

Hi Barry,
Karsten's Motor2 node should be a big help.
May I suggest forming the two screws and bottle in .3dm, a la crankshaft etc.
Also a chart of the "engineering" would be helpful.
Ratio of helix turns to bottle turns.

Bottle turns 90 degrees as helix turns 4 times 360 degrees.
So the master slider (or quartz clock/timer/oscillator node) would have to be divided by 16 to feed the rotation node controlling bottle rotation.
It may also have to be negated for CW vs CCW.
The master slider would also, via a math node, directly feed two rotation nodes, input x, one for each screw. (One signal negated for CW vs CCW.)
And adjust frames for the LH screw's rotation node, and for the bottles rotation node.

Bottle moves x units to the right, from x1 to x2.

Does the screw need a bit of groove at negative x axis bottle width?
Rotation ccw/cw etc for the 3 objects.

Due to current work load, there is not much time to play with MoI.
- Brian

---

Barry, to answer your questions:

The axis of rotation for your second screw is determined by the Frame input of your Rotate node.
The Frame input is fed by the point x,y,z node, which needs to have its y input set by a Basic/Constant of y-value of the second screw's axis.

The direction of rotation can be reversed by running the x-axis input of the rotate factory through a negative Math node.
I used Math node of a-b, with input a = constant 0, and input b coming from the quarts clock. (I have not seen a straight minus node.)
(This is a going upstream explanation, so the flow is sort of backwards.)

(I am a rank amateur at the nodes:-)

- Brian

A picture would be very nice, but I am about out of upload bytes...
I'm working off of the motor2 node, for modification experiments.
The crankshaft represents the RH screw, and moved up by Y, would represent the LH screw
The red piston represents the bottle.
Obviously there must be some modifications in the nodes, and swap in screws and the bottle, and adjust orientations, but the basics are there.
The quartz node is nice to use.

---

Hi Brian,
thanks for the pointers got the screws to rotate ok.
Reversed the direction by starting the LH Screw at max revolution and subtracting the slider position.
Ie: Rh Screw starts at Min and LH Screw starts at Max.
Going to try and add the bottle movement in and if possible to check for interference as Karsten did
with the motor node.
Again thanks
Barry

---

:-)

---

Hi,
I am using node editor v0.93 and cannot find the quartz clock/timer/oscillator node that Brian mentioned in a previous post.
Can someone point me where to get it and how to install it plus how to use it instead of a slider to animate my Screw model.
Thanks
Barry

---

Hi Barry.
under the subdirectory "nodes," Quartz is inside the basic.js file. It is commented out.
Just remove all but the first //.
I do not know why Max has not activated it.
Output is a "numarray."
Maybe there is supposed to be some input to it that was not completed. (this.addInput("Hz","numarray");)
Maybe Quartz node can feed a second Quartz node? Have to try it...

Quartz may be from the original source of nodes (?)

Default Quartz runs from zero to 359, which yields 360 degrees, which may be a full circle rotation...

Quartz has 2 modes.
Cycled mode runs from e.g 0 degrees to 359 degrees, then starts over at 0.
Tictac mode gets to the end of the count, then runs backwards to the begin count, e.g.zero

- Brian
I think of it as an electronic quartz crystal oscillator, or a clock, etc.

---

Hello Friends
I want to share with you
this research done, to draw curves
Math(Roulette Curve) ,
I have used Vector to represent
"Locus "of the points
which then turn into curves ...
I also attached a variant in 3d
very interesting, at least I hope....
For those interested this is the link:https://www.mediafire.com/?l58wc87s75uw6j6
Good in-depth
best
al

---

Hello Al,

thanks for sharing - very interesting - the Vectors looks great!



A look to the curvature also says perfect:-)


Have a nice day
Karsten

Image Attachments:
Roulette-Curvature.png  Roulette-Vectors.png 

---

Remember the Line Web! ;)

http://moi3d.com/forum/index.php?webtag=MOI&msg=3666.1

---

Hello Pilou,

I do not understand what I should remember!?

Line Web is possible since Max has made pointarrays and I made patharrays. You have tested it already.
http://moi3d.com/forum/index.php?webtag=MOI&msg=7777.330
The example makes nothing else then:
http://moi3d.com/forum/index.php?webtag=MOI&msg=7777.317
http://moi3d.com/forum/index.php?webtag=MOI&msg=7777.163
or in a more complicated way:
http://moi3d.com/forum/index.php?webtag=MOI&msg=7777.111
For the inspiration I had please google: helix bridge singapore

Or do you think that we have to have a line web node?
Have a nice day and please let me know

Karsten

---

<< Or do you think that we have to have a line web node?

Will be perfect because it's a tricky thing for make easily some regulate surfaces!

---

Hhhmm!
That's all!?!

Image Attachments:
LineWeb.png 

---

I will try that! :)

Just about indepth of the beast of a node...(just by curiosity because i will never code that)
You must re-create all the function or you recall an existing function (here Line Web) somewhere ?

Else for a Node Line Web itself
- Nbs point by curves
- Nbs of curves
- Variation of curves (distort curves)
another infinite variations! :)

Ps Can you post your node because I don't obtain the same! :(
(or maybe i don't make the good process ?
http://moiscript.weebly.com/uploads/3/9/3/8/3938813/line_web.nod

---

Hello Pilou
You have to set-up "cross " in the node preferences,
(mpath array )
al

---

@Al
Ahhh yes! Some indispensable hidden things! Bravo!
(Now Lineweb native is more simple! ;)
But as soon as more nodes will added that will be rocking!

Maybe the Info window must be open as soon has a new node is created!

---

Distort ? By Max Smirnov http://moi3d.com/forum/index.php?webtag=MOI&msg=6659.13
For crazy vegetables! :)

---

Hello Friends
an experimental test of a sphere tasselation
with base Icosahedron
link:http://www.mediafire.com/file/3h0nk02r0u11hhl/Geodesic_Tasselation.rar
Have a nice day to all
al

---

Al et al,

I have had no opportunity to play with node editor for the last couple of months,
but this weekend I teased apart your Spir-Curve nod to comprehend your method.

After researching roulette curves, I started from scratch to produce this very simple scheme (no trig) based on your method for Trochoid curves.

It can also create Epicycloids by flipping the vectors
(i.e. multiplying by -1 bottom most node)

Now I am going to try and get my head around your geodesic nod.
It looks amazing!

Have a great weekend

James

Image Attachments:
Trochoid.jpg 

---

Hi,
I'm running an animation with the node editor and was wanting to hide edges.
I've tried hiding them prior to running the animation but this does not work.
Is it possible to have a node to hide them ?
Barry

---

Hi Barry.

The code which loads the .3dm object is located here:
Under Node/Objects/Get by name

Perhaps a line could be added there. I do not know how:-(
The following code did not work:
// TEST edge hidden code (BAD)
this.inputobjects.edges.setProperty('hidden', true);
// End Test Code

- Brian

---

Show messages:  1-8  …  289-308  309-328  329-348  349-368  369-388  389-408  409-428  …  1849-1859