Full Version: Nodebundle for playing with nodes

Show messages:  1-13  …  954-973  974-993  994-1013  1014-1033  1034-1053  1054-1073  1074-1093  …  1854-1859

Thread Split: Some posts in this thread have been moved here

Hi Al,

I know my node file is a bit of a mess. It was the result of pure "ad hocery".
I was just playing around to see what unfolded. No plan.

I probably should have gone back and optimised the circuitry before posting.
Thank you for doing this. I look forward to seeing how you have approached it.

James

UPDATED:

P.S. I have just started to see what you have done. I could not help noticing,
once adding up the nodes inside the expanded macros, that you have
used more than twice as many nodes for a similar result. That is not a criticism;
I know that node reduction does not necessarily reduce the computation load on running,
and in the end it doesn't much matter how many nodes it takes, if lag time between
clicking "RUN" and the generation of geometry is reduced to a minimum.In the end,
really that is all that is important.


UPDATED:
On your prompting, I have now replaced surfTria.nod file in earlier post with simplified
version (Essentially it is the my same method encapsulated in a macro):

http://moi3d.com/forum/index.php?webtag=MOI&msg=7777.1004

---

Message 7777.1015 was deleted

---

Hi All,

Having mapped surfaces with hexagon based tiling patterns with "HexTesselation"macro,
I am investigating the manipulation of individual tiles. Below is an experiment along these lines.


James

UPDATED problem solved (new image & .nod file)

Image Attachments:
apertureVari3.jpg 

---

Hi James and Friends
I saw your answer, and I checked the surfTria file again
adjusted by you ..
I must say that the macro ExTasselation does not respond in a timely manner
to the Row and Col inputs as well as the output exagon number
at this link:
http://www.mediafire.com/file/orqpc5jigc8lovh/M_ExGrid.zip/file
you will find the Macro that I have rectified, following
a method different from yours, but that presents an exact answer
between input data and output data ...
I did not have time to see the last files posted
I promise to do it as soon as possible
Have a nice day
alberto

---

Thanks Al,

>> M_ExGrid <<.

I look forward to looking at what you have done.
If it could reduce the generation of geometry of apertureVari3.nod, for example, that would be brilliant.

I am just glad that NE is been given deserved attention again.
James

---

Hi All,

Attached is nod file for generating a collar with pattern transition.
As always, be aware that generation of geometry may take half a minute or so.

James

---

Very interesting !
Do you think it's possible to create a nod to flow a module on a model ? (same as Paneling tool in Rhino)
module and model are create on my scene
At his time, i use Array and Flow command to do that but it's not flexible and parametric
see my example in screenshot
Thanks

---

Message 7777.1021 was deleted

---

waoouu ! Great !
it's a good start !
i have tested with a knurl pattern but the result is not uniform, the modules are streched and overlap
thanks again

---

Hi Finema and friends
at this link:
http://www.mediafire.com/file/kqm1csr5w6b2g0o/31-05-Bottle_SimPanelingTool.zip/file
you will find the file, to adapt the object to the surface,
as you will see the approach is different from the amount that you have
posted James ... I think this also has its validity
Certainly it is not the paneling that can be achieved with
Paneling Tools- or Rhino's Morph Box (Grasshopper)
but it's always a good start for Moi-
You just have to open the file and then run it,
you will see different parameters, rows, columns, etc etc ...
change them to see how they work-
Have a nice day to all
alberto

---

Hi Finema,

This is an alternative simpler approach:

Click RUN
If nothing happens, click "Surface Index" switch

The target surface should be index either 0 or 1.
In the event nothing still happens, try changing "const" node values to 2 & 3

& if you desire the bottle to be shown, click "switch" to reveal

James

for .3dm & .nod file see:
http://moi3d.com/forum/index.php?webtag=MOI&msg=7777.1043

---

Hi Alberto,
How i can use it ?
Must i name object ?
Thanks a lot.

---

Thanks a lot James
It's very good
But i have an error when i want to change the bottle.
UNSUPPORTED POLYGON TYPE 15

---

Hi Finema
you simply have to open the file
and run ... all the data is in the file, there are not any
referenced objects
best
al

---

Al,
You don't join a 3dm file
I think some .js are missing in my node editor
mflowObj is red
thanks

---

Hi Finema,

>> error when i want to change the bottle. UNSUPPORTED POLYGON TYPE 15 << .

The issue is the indexing of the surfaces of the bottle.

I have updated my previous post with new nod file
& instructions

James

---

Hi James
That don't work for me
Nothing happen when i modify the bottle or i have message error
I have change index , quit , reopen but no way
Thanks again for your time

---

Finema, is the modified bottle named " bottle"?

---

yes
i join the 3dm file with the new bottle
thanks

---

It works with "surface index" switch set to 0
Did you read instruction on my earlier post?

---

Show messages:  1-13  …  954-973  974-993  994-1013  1014-1033  1034-1053  1054-1073  1074-1093  …  1854-1859