MoI in Develop3D magazine
All  1-4  5-11

Previous
Next
 From:  DannyT (DANTAS)
1722.5 In reply to 1722.4 
Hey mictu,

Same here.

>>It can handle some of the surfacing and mechanical tasks that seem to take forever in parametric history based systems in a matter of minutes.

I can totally relate to that! :D

Cheers
~Danny~
  Reply Reply More Options
Post Options
Reply as PM Reply as PM
Print Print
Mark as unread Mark as unread
Relationship Relationship
IP Logged

Previous
Next
 From:  David (BLEND3D)
1722.6 
I felt that the reviewer while stating that he was stepping into the maelstrom somewhat pandered to the three user bases. Not as informative as it may have been intended.

I must say though I'm glad to see MoI in reviews as the exposure will ultimately expand the user base. Michael will be with income and the incentive to continue developing this unique, easy to use, economical and accurate application.
  Reply Reply More Options
Post Options
Reply as PM Reply as PM
Print Print
Mark as unread Mark as unread
Relationship Relationship
IP Logged

Previous
Next
 From:  manz
1722.7 In reply to 1722.4 
>>I have been designing products for 20 years and BC (Before CAD)

You would need to go back a little further to get to BC(before CAD). I was using the early versions of Autocad in the early 80`s.
What about "Sketchpad" (1963)
  Reply Reply More Options
Post Options
Reply as PM Reply as PM
Print Print
Mark as unread Mark as unread
Relationship Relationship
IP Logged

Previous
Next
 From:  Michael T. (MICTU_UTCIM)
1722.8 In reply to 1722.7 
Sorry manz, I was refering to my own personal exposure to CAD :-) Drafting board to Computervisions Personal Designer software. I think it is DOS freeware now :-)

Michael T.
Michael Tuttle a.k.a. mictu http://www.coroflot.com/fish317537
  Reply Reply More Options
Post Options
Reply as PM Reply as PM
Print Print
Mark as unread Mark as unread
Relationship Relationship
IP Logged

Previous
Next
 From:  manz
1722.9 In reply to 1722.8 
Hi Michael T,

No personal disrespect intended, I was not sure if you where aware of the products available more than 20 years ago. Sorry if you thought more than that (it is my fault)

Regards,

Manz (steve)
  Reply Reply More Options
Post Options
Reply as PM Reply as PM
Print Print
Mark as unread Mark as unread
Relationship Relationship
IP Logged

Previous
Next
 From:  jbshorty
1722.10 
Hi. If it makes you feel any better, i think you're both old!!! :)

jonah
  Reply Reply More Options
Post Options
Reply as PM Reply as PM
Print Print
Mark as unread Mark as unread
Relationship Relationship
IP Logged

Previous
 From:  Michael T. (MICTU_UTCIM)
1722.11 In reply to 1722.10 
Thanks guys, I was aware of the availability of the 3D software 20 years ago, but you have to remember that "our" employers were in control of what was purchased, right or wrong (usually wrong because they are not designers).

Now if you all don't mind I have to put my teeth in a cup and hope that I can remember where I put the cup in the morning. So now I can go to bed, wake up (hopefully) and use my AARP discount for breakfast!!!

Funny stuff folks!

Michael T.
Michael Tuttle a.k.a. mictu http://www.coroflot.com/fish317537
  Reply Reply More Options
Post Options
Reply as PM Reply as PM
Print Print
Mark as unread Mark as unread
Relationship Relationship
IP Logged
 

Reply to All Reply to All

 

 
 
Show messages: All  1-4  5-11